Main: air-cooled Roots pump , Roots liquid ring vacuum unit
1. Always check the position of the oil level. If it does not meet the requirements, it must be adjusted to meet the requirements. When the Roots pump is running, the oil level is up to the center of the oil mark.
2, the oil change period according to the actual conditions of use and whether it can meet the performance requirements, etc., at the discretion of the user. General new Roots pump, when pumping clean and dry gas, it is recommended to change the oil once a month or so. After you can't see the black metal powder, you can extend the oil change period later.
3, often check the oil quality, found that the oil should be replaced in time to replace the new oil, to ensure that the Roots pump works properly.
4. Under normal circumstances, the Roots pump should be inspected after 2000 hours of operation, check the aging degree of the silicone seal, check whether the exhaust valve is cracked, and clean the dirt deposited on the valve plate and the exhaust valve seat. Parts in the Roots pump chamber, such as rotors, rotary vanes, springs, etc. Generally cleaned with gasoline and dried. After cleaning the rubber parts, dry them with a dry cloth. Wash the assembly with care. hurt.
5. Add bearing lubrication oil to the bearing body. Observe that the oil level should be at the center line of the oil mark. The lubricating oil should be replaced or replenished in time.
6, check the Roots pump pipeline and joints with or without looseness. Turn the Roots pump by hand to see if the Roots pump is flexible.
7. After re-assembly, it should be tested. Generally, it must be operated for 2 hours and oil change twice. Because it will leave a certain amount of volatile substances in the Roots pump during cleaning, it will be put into normal operation after it is running normally.
8. Start the motor. When the Roots pump is running normally, open the outlet pressure gauge and the imported Roots pump. After it shows the proper pressure, gradually open the gate valve and check the motor load.
9, try to control the flow and head of the Roots pump within the range indicated on the sign to ensure that the Roots pump operates at the high efficiency point of Zui, in order to obtain the large energy-saving effect of Zui.
10, when the Roots pump is to stop using, first close the gate valve, pressure gauge, and then stop the motor.
11, during the operation of the Roots pump, the bearing temperature can not exceed the ambient temperature of 35C, the high temperature of zui must not exceed 80C.
12, Roots pump in the work * months, after 100 hours to change the lubricant, after each 500 hours, change the oil once.
13, often adjust the packing gland to ensure that the drip leakage in the packing chamber is normal (in order to drip out is appropriate).
14, regular inspection of the wear of the bushing, should be replaced in time after the wear is large.
15, Roots pump is long-term use, the pump should be completely dismantled, dry the water, the rotating parts and joints are coated with grease, and kept safe.
16, when the Roots pump is used in the cold winter season, after parking, the water plug of the lower part of the pump body should be unscrewed to release the medium to prevent freezing cracks.
1. Always check the position of the oil level. If it does not meet the requirements, it must be adjusted to meet the requirements. When the Roots pump is running, the oil level is up to the center of the oil mark.
2, the oil change period according to the actual conditions of use and whether it can meet the performance requirements, etc., at the discretion of the user. General new Roots pump, when pumping clean and dry gas, it is recommended to change the oil once a month or so. After you can't see the black metal powder, you can extend the oil change period later.
3, often check the oil quality, found that the oil should be replaced in time to replace the new oil, to ensure that the Roots pump works properly.
4. Under normal circumstances, the Roots pump should be inspected after 2000 hours of operation, check the aging degree of the silicone seal, check whether the exhaust valve is cracked, and clean the dirt deposited on the valve plate and the exhaust valve seat. Parts in the Roots pump chamber, such as rotors, rotary vanes, springs, etc. Generally cleaned with gasoline and dried. After cleaning the rubber parts, dry them with a dry cloth. Wash the assembly with care. hurt.
5. Add bearing lubrication oil to the bearing body. Observe that the oil level should be at the center line of the oil mark. The lubricating oil should be replaced or replenished in time.
6, check the Roots pump pipeline and joints with or without looseness. Turn the Roots pump by hand to see if the Roots pump is flexible.
7. After re-assembly, it should be tested. Generally, it must be operated for 2 hours and oil change twice. Because it will leave a certain amount of volatile substances in the Roots pump during cleaning, it will be put into normal operation after it is running normally.
8. Start the motor. When the Roots pump is running normally, open the outlet pressure gauge and the imported Roots pump. After it shows the proper pressure, gradually open the gate valve and check the motor load.
9, try to control the flow and head of the Roots pump within the range indicated on the sign to ensure that the Roots pump operates at the high efficiency point of Zui, in order to obtain the large energy-saving effect of Zui.
10, when the Roots pump is to stop using, first close the gate valve, pressure gauge, and then stop the motor.
11, during the operation of the Roots pump, the bearing temperature can not exceed the ambient temperature of 35C, the high temperature of zui must not exceed 80C.
12, Roots pump in the work * months, after 100 hours to change the lubricant, after each 500 hours, change the oil once.
13, often adjust the packing gland to ensure that the drip leakage in the packing chamber is normal (in order to drip out is appropriate).
14, regular inspection of the wear of the bushing, should be replaced in time after the wear is large.
15, Roots pump is long-term use, the pump should be completely dismantled, dry the water, the rotating parts and joints are coated with grease, and kept safe.
16, when the Roots pump is used in the cold winter season, after parking, the water plug of the lower part of the pump body should be unscrewed to release the medium to prevent freezing cracks.
Bee Pollen comes from
nature, is the bee from the flowers (nectar plants and pollen plants)
flowers collected in the pollen grains, and joined the special glandular
secretions (nectar and saliva) mixed into an irregular Flat round shape. Bee
pollen has a unique natural health care and medical and cosmetic value,
is more and more people know, is a high-protein low-fat nutritional
health food, known as "all-round nutrition food" "concentrated natural
medicine library" "Oral cosmetics" and so on, is the treasure of human natural food.
We provide rape pollen, tea pollen, sunflower pollen and mixed pollen, they are all collected from our professional green beefarm base.
We have applied the certificate of ISO, HACCP and GMP, making sure the quality of bee products.Bee Pollen
Bee Pollen,Bulk Bee Pollen,Natural Bee Pollen,Mixed Bee Pollen
Easy Food (Jiaxing) Co., Ltd. , https://www.jxeasyfood.com