Shanghai Xitang Biotechnology Co., Ltd. 021-55229872, 65333639
Rat hyaluronic acid (HA) ELISA kit instruction manual
 ( used in serum, plasma, cell culture supernatants and other biological fluids )
principle
This experiment used double antibody sandwich ABC-ELISA. The anti-rat HA monoclonal antibody was coated on the microtiter plate, the standard and the HA in the sample were combined with the monoclonal antibody, and biotinylated anti-rat HA was added to form an immune complex attached to the plate, horseradish peroxidation. The enzyme-labeled Streptavidin is combined with biotin, and the substrate working solution is blue. Finally, the stop solution sulfuric acid is added, and the OD value is measured at 450 nm. The HA concentration is directly proportional to the OD value. The HA can be obtained by drawing a standard curve. concentration.
Kit composition ( 2-8 ° C preservation)
Coated Wells | 96 holes | Enzyme Conjugate | 12ml |
10× specimen dilution (Sample Buffer) | 12ml | 20×Wash Buffer | 50ml |
Standards: 2000ng/bottle | 2 bottles | Substrate working fluid (TMB Solution) | 12ml |
Primary antibody working solution (Biotinylated Antibody) | 12ml | Stop Solution | 12ml |
Prepare reagents and collect blood samples
1. Collection of specimens: serum, plasma (EDTA, citrate, heparin anticoagulation), cell culture supernatant, tissue homogenate, etc., as early as possible, stored at 2-8 ° C for 48 hours; longer time must be frozen (-20 ° C Or -70 °C) to avoid repeated freezing and thawing.
2. Standard solution preparation: Add 1ml of distilled water before use and mix well to form 2000ng/ml solution. Set 8 tubes of standard tubes, and add 300 ul of standard dilution solution to each tube. Add 2000 ng/ml of the standard solution to the first tube and mix 300 ul, then aspirate 300 ul with the sampler and transfer to the second tube. Repeat the dilution in this way, and remove 300 ul from the seventh tube and discard it. The eighth tube is a blank control.
3. The 10× specimen dilution was diluted 1:10 with distilled water (example: 1 ml concentrated dilution + 9 ml distilled water).
4. Washing solution: diluted 1:20 with distilled water (example: 1 ml concentrated washing solution added to 19 ml of distilled water)
Test procedure
1. Loading: Add 100 ul of standard or sample to be tested in each well. Mix the reaction plate thoroughly and let it stand at 37 °C for 120 minutes.
2. Wash the plate: Wash the plate thoroughly with washing solution 4-6 times, and dry it on the filter paper.
3. Add 100 ul of the first antibody working solution to each well. The reaction plate was thoroughly mixed and placed at 37 ° C for 60 minutes.
4. Wash the board: the same as before.
5. Add 100 ul of enzyme-labeled antibody working solution per well. The reaction plate was placed at 37 ° C for 30 minutes.
6. Wash the board: same as before.
7. Add 100 ul of substrate working solution to each well and let it react at 37 ° C for 15 minutes in the dark.
8. Add 100 ul of stop solution to each well and mix.
9. Measure the absorbance at 450 nm using a microplate reader within 30 minutes.
Result calculation and judgment
1. All OD values ​​should be subtracted from the blank value before calculation.
2. Take the standard products 1000, 500, 250, 125, 62.5, 31, 15.6, 0 ng/ml as the abscissa and OD as the ordinate. Draw on the coordinate paper and draw the standard curve.
3. Find the corresponding HA content on the graph based on the sample OD value.
Kit performance
1. Sensitivity: The minimum HA detection concentration is less than 9 ng/ml.
2. Specificity: Recombinant or natural rat HA can be detected simultaneously. Does not cross-react with other cytokines in rats.
3. Repeatability: The coefficient of variation in both the plate and the plate is less than 10%.
Precautions
1. It is recommended to make double holes for the above standard holes and samples to be tested. The standard curve should be made at the same time for each measurement.
2. The washing process is critical. Insufficient washing will result in an accuracy error and an erroneous rise in the OD value.
3. After the slats are opened, the remaining slats should be sealed again to keep the slats dry .
4. This kit should be stored in a 4oC refrigerator.
5. This kit is for scientific research only and cannot be used for clinical diagnosis!
Laser Distance Sensor
Leading Laser Measure Module Factory in China
The World's First single transmitting single receiving design laser module, which has a big help to reduce producing cost and power consumption of the laser distance sensor.
This Laser distance sensor has high Accuracy up to ±1 mm, working as phase measure, which support RS232/RS422/RS485/Arduino to TTL communication.
This laser distance module is widely used in the Laser Distance Meter industry, also a very good choice for the Industrial applications. Most of measuring tools manufactures is purchasing from us in China.
Product Specifications:
|
Accuracy
|
±1
mm (0.04 inch)
|
|
Measuring
Unit
|
meter/inch/feet
|
|
Measuring
Range (without Reflection)
|
0.03-150m
|
|
Measuring
Time
|
0.1~3
seconds
|
|
Laser
Class
|
Class
II
|
|
Laser
Type
|
635nm,
<1mW
|
|
Size
|
45*25*12mm
(±1 mm)
|
|
Weight
|
About
10g
|
|
Voltage
|
DC2.0~3.3V
|
|
Electrical
Level
|
TTL/CMOS
|
|
Frequency
|
10Hz
|
|
Operating
Temperature
|
0-40 ℃ (32-104 ℉ )
|
|
Storage
Temperature
|
-25~60 ℃ (-13~140 ℉)
|
Range Sensor,Laser Distance Module,Distance Sensor,Laser Measure Sensor
Chengdu JRT Meter Technology Co., Ltd , https://www.cdlaserdistancesensor.com